Armour is the part of the jacket that meets the impact, and its level is one of the few genuinely comparable numbers in riding gear. But the number is not a score. It describes how much force a pad transmits in a defined test, and it says nothing about whether the pad is in the right place when you fall.
Protector standards and levels
| Protector | Standard | Levels | What the level means |
|---|---|---|---|
| Shoulder, elbow, knee, hip | EN 1621-1 | Level 1 and 2 | Level 2 transmits less force in the test |
| Back protector | EN 1621-2 | Level 1 and 2 | Separate test and limits from limb armour |
| Chest protector | EN 1621-3 | Level 1 and 2 | Separate chest impact test |
| Foam comfort pad | No standard | None | Cushioning only, not certified impact protection |
| Airbag vest | Separate system | Not EN 1621 | Electronic or tether-triggered inflation |
Two labels that get mixed up
A jacket label may say EN 17092 AA, while the shoulder pad says EN 1621-1 Level 2. These are different standards answering different questions. EN 17092 classifies the garment's abrasion, tear and seam performance. EN 1621-1 classifies the impact protector itself.
Neither label replaces the other. A high garment class with no armour leaves the joint unprotected against impact, and excellent armour in a loose jacket can move away from the joint before it is needed. Read both, then check the fit.
What Level 1 and Level 2 measure
EN 1621-1 tests limb protectors by dropping a defined mass onto the pad and measuring how much force is transmitted through it. The standard sets a maximum transmitted force for each level, and Level 2's limit is roughly half of Level 1's. The test is done at a specified energy and on defined anvils.
Level 1 is the baseline that most riding gear uses. Level 2 requires the pad to absorb more of the same impact, usually through thicker or more sophisticated material. Both are minimum requirements, and a pad that only just passes Level 1 is not equivalent to one that passes comfortably.
The test uses a defined impactor and anvil, and it measures force transmitted through the pad, not the injury you will suffer. A pad can pass Level 2 on the test rig and still be uncomfortable or misplaced in a jacket. The level is useful for comparing pads, but it is not a prediction of outcome.
The comfort cost of Level 2
Level 2 pads are often thicker, denser and stiffer. In a jacket with tight pockets, that can mean the pad sits proud, restricts movement or presses into the shoulder. In hot weather, the extra material holds heat and reduces airflow through the area.
A pad that is uncomfortable is a pad that gets removed, folded or left at home. That is a worse outcome than a Level 1 pad that stays in place. The best armour is the highest level you can wear comfortably for the whole ride, not the highest level printed on the box.
Fit and coverage beat the level
The pad must cover the joint in the position you ride in. Shoulder pads should sit on the point of the shoulder, elbow pads over the elbow, knee pads over the kneecap and hip pads on the hip bone. When you bend your arm or sit on the bike, the pad should not slide to the side.
Adjustable pockets, straps and a close fit matter more than the level. A Level 2 pad that has rotated is protecting the wrong area. Check the armour after putting the jacket on, and again after sitting on the bike. If it moves, fix the fit before upgrading the pad.
Back and chest protectors use different standards
Back protectors are certified under EN 1621-2, with Level 1 and Level 2. Because the back is a larger area and the consequences of a spinal impact are different, the test and the force limits differ from limb armour. A Level 2 limb pad tells you nothing about back protection.
Chest protectors fall under EN 1621-3, again with levels. Many jackets have a chest pocket but no certified chest pad. If chest protection matters to you, check that the pad carries the standard and fits the pocket, rather than assuming the pocket is enough.
Back protector length is as important as its level. A short pad that covers only the upper back leaves the lower spine exposed, while an overlong pad can push into the seat or ride up when you lean forward. Try the protector in the jacket, on the bike, and check that it covers the spine without restricting movement.
When Level 1 is the rational choice
For slow city commuting in a hot climate, Level 1 armour that is thin, flexible and stays in place can be the better real-world choice. It is easier to wear all day, and the impact speeds are lower. Add a certified back protector if the jacket accepts one.
For fast road riding, touring at highway speed and track use, Level 2 is easier to justify, especially at the shoulders, elbows and knees. Whatever the level, replace armour that has taken a significant impact, hardened, cracked or lost its shape, and follow the manufacturer's guidance.
Checklist
- Check the armour marking separately from the garment class.
- Confirm the level for each pad, not just for the jacket as a whole.
- Try the jacket on and check that shoulder and elbow pads stay on the joint.
- Sit on the bike and re-check the knee and hip pads.
- Ask whether the back protector is included and certified to EN 1621-2.
- Consider heat and bulk before choosing Level 2 everywhere.
- Replace pads that have taken a hard impact or lost their shape.
Questions
Is Level 2 always safer than Level 1?
Level 2 transmits less force in the standard test, so it offers more margin in that specific impact. In practice, a Level 1 pad that fits and stays in place can protect better than a Level 2 pad that is uncomfortable or misaligned. Fit and coverage come first.
Can I upgrade the armour in my jacket?
Often yes, if the pockets are the right size and shape and the maker offers compatible pads. A pad that is too thick can sit proud or distort the jacket. Check the pocket dimensions and the manufacturer's guidance before buying a replacement.
Is back armour included with most jackets?
Many jackets include a thin foam back pad, which is not the same as a certified EN 1621-2 protector. Check the label on the pad itself. A certified back protector is often sold separately and should be matched to the pocket.
Does armour need replacing after a crash?
Yes, if the pad has taken a significant impact, is cracked, compressed or deformed. Some foams recover visually but lose performance. Follow the manufacturer's guidance, and replace the pad rather than the whole garment where possible.