Helmet replacement is usually discussed as a rule of thumb: crash equals new helmet. The rule is right more often than not, but the reasoning matters, because riders then apply it to a helmet that rolled off a seat and ignore the one that spent four summers in a hot car. What decides the answer is what the energy-absorbing liner has been through, and what the manufacturer says about the shell and materials.

What happened, and what to do

EventActionReason
Head hit the ground or a vehicleReplaceThe liner has absorbed energy
Struck by an object while wornReplaceLocal compression may be invisible
Empty helmet fell from a seatInspect; replace if unsureLess mass, but the liner can still compress
Helmet fell with contents or was sat onReplaceLoad concentrated in one area
Years of regular useFollow the maker's service lifeFoam and adhesives age
Stored in heat or direct sunInspect and shorten the lifeHeat accelerates ageing
Bought second-hand, history unknownDo not rely on itNo way to know its impacts

The liner is the part that does the work

The shell spreads the load and resists penetration. The liner, usually expanded polystyrene, crushes to absorb energy, and crushing is permanent. A shell can flex and spring back; the foam behind it cannot. That is why a helmet can look untouched after a hard knock and still have a compressed area inside. If the liner has done its job once, it has less capacity to do it again in the same place.

Impacts that end a helmet's life

Any impact where your head hits something while wearing the helmet is a replacement, including low-speed falls, a clip from a mirror and a helmet struck by a falling object. The energy may be small, but the liner does not recover and you cannot see the compression from outside. Do not wait for the shell to crack; by then the liner has already absorbed what it could.

Drops and knocks

An empty helmet falling from a seat is a different case from a helmet with a head inside it, because there is much less mass behind the impact. Manufacturers differ in what they advise, and some ask for inspection rather than automatic replacement. Inspect the shell, the liner and the mechanism, and if you cannot satisfy yourself that nothing compressed, replace it. The cost of a helmet is small against the uncertainty.

Age, heat and storage

Foam, adhesives and plastics age. Sunlight, heat cycles, sweat and solvents all speed that up, and a helmet stored in a hot vehicle or a sunny shed has lived a harder life than its age suggests. Many manufacturers state a service life from first use and a limit from manufacture; follow the manual for your model. A helmet with an unknown history, bought second-hand, has no reliable age at all.

Inspecting a helmet after a hit

Look along the shell for cracks, white stress marks and separation between the shell and the trim. Press the liner gently around the impact point and compare it with the other side; a soft or flattened area is a sign of compression. Check the strap webbing, the buckle, the visor mechanism and the gaskets. Then check the fit: a helmet that has lost liner volume will sit differently, which is another reason to retire it.

Retiring it and choosing the next one

Do not sell, gift or keep a crashed helmet in use. Cut the strap or mark the shell so nobody else wears it, and keep it only as a display object if you want the reminder. The replacement should be certified for where you ride, fit as well as the old one did when it was new, and come with a manual and a receipt. Registering the helmet helps if a recall is issued later.

Second-hand helmets and unknown history

A used helmet may look perfect and still have a compressed liner or a cracked shell from an impact the seller does not mention. You cannot inspect the energy-absorbing foam inside a assembled helmet, and you cannot verify its storage history. The safe default is to avoid second-hand helmets unless you know the owner and the history.

The same caution applies to helmets stored in a hot shed or a car for years. Heat ages foam and adhesives, and the shell may have been exposed to solvents. A bargain on a used premium helmet is not a bargain if the protection has already been spent.

Checklist

  • Replace any helmet worn during a head impact, however slow.
  • Inspect shell, liner, strap, buckle and visor mechanism after a drop.
  • Compare liner firmness on both sides of the impact point.
  • Check the manufacturer's service life and count from first use.
  • Keep the helmet out of hot vehicles and direct sun.
  • Cut the strap of a retired helmet so it cannot be reused.
  • Buy the replacement certified for the country you ride in.

Questions

Can I keep a helmet after a low-speed fall?

If your head was inside it when it hit something, replace it. Low speed still compresses the liner, and the damage is usually invisible. The shell surviving is not evidence that the liner did.

Does a scratched shell need replacing?

A cosmetic scuff does not. A crack, a deep gouge, delamination or separation from the trim does, because the shell's structure may be compromised. Inspect the liner around the area as well, since the impact that marked the shell also reached the foam.

How long does a helmet last?

Manufacturers publish service lives, commonly a number of years from first use and a limit from the date of manufacture. Heat, sweat, sunlight and storage change that in practice. Follow the manual for your model rather than a general rule.

Can I sell or give away a crashed helmet?

No. You cannot verify what it has absorbed, and the next owner cannot either. Retire it, cut the strap and dispose of it responsibly. Selling a damaged helmet as serviceable is dishonest and dangerous.

Go deeper