Boot covers are the least discussed piece of rain gear and one of the most effective per unit of cost. They are also the piece most likely to be bought in the wrong size. A cover that is too tight will not go over a riding boot; one that is too loose will flap, slide on the peg and let water in at the top.

Boot cover types compared

TypeSoleRain coverageWalkingBest for
Minimal overbootOpen soleUpper and lacesShort distancesCommuting with waterproof boots
Gaiter styleOpen sole, tall shaftUpper and lower legShort distancesHeavy rain with overpants
Full-sole coverFull rubber soleWhole bootLonger distancesWalking off the bike in rain
Shifter-patch coverOpen or fullUpper, reinforced left toeShort distancesHigh-mileage commuters

What overboots cover, and what they do not

A boot cover keeps rain off the upper and laces of your boot, but water does not only fall from above. It runs down your overpants, reaches the top of the boot and soaks into the lining. That is why the height of the cover and the overlap with your trousers matter as much as the fabric.

Covers also do nothing for the sole, which is why many designs leave the sole open. The boot's own sole contacts the peg and the ground, and the cover wraps around the upper. If you need protection for the sole, you need a waterproof boot rather than a cover.

Soles: cut-out, full and grip

Most motorcycle overboots have an open sole or a large cut-out, so the boot's rubber sole meets the peg directly. That preserves feel and grip, and it avoids a layer of slippery fabric between your foot and the ground. The trade-off is that the boot sole gets wet, which is acceptable if the boot itself is water-resistant.

Some covers have a full sole for walking in wet conditions. These are better off the bike but can be slippery on pegs and reduce feel at the controls. Check the sole material and the tread pattern; a smooth, hard sole is dangerous on a wet footpath and on a metal peg.

The top seal and the shifter

The top of the cover needs to close around the leg or the boot cuff. Elastic alone can leave a gap when the trouser leg is bulky. A drawcord or a hook-and-loop strap holds the cover up and reduces the chance of water running inside. The cover should sit under the overpant hem, not over it, so water sheds from the trouser onto the cover.

The gear shifter wears through the top of the left boot, and it will wear through a cover in the same place. Look for a reinforced shifter patch, usually a rubber or leather panel. Without one, the cover develops a hole exactly where rain enters, often within a few weeks of daily use.

Sizing over riding boots

Boot covers are sized for the boot they go over, not for your shoe size. A touring boot is wider and taller than a sports boot, and an adventure boot is wider again. Measure the boot's height and the circumference at the calf, then compare with the cover's stated range rather than guessing.

The opening at the bottom must pass over the heel and the toe. A cover with a narrow opening can be forced on when new and then split at the seam. Check that the material has some stretch or that the opening has a zip or hook-and-loop closure. Trying them on over your own boots is the only reliable test.

Heat, walking and wear

The right cover sits close to the exhaust and the engine on many bikes. Synthetic fabrics can melt or scorch, and a hole in that area lets water straight into the boot. Keep the cover clear of hot parts, and check the inner ankle after a ride. A heat-resistant panel is worth having if your bike routes the exhaust close to the foot.

Walking wears covers quickly. The sole edge scuffs, the heel drags and the fabric creases at the ankle. If you plan to walk any distance, choose a cover with a reinforced sole edge and a shaped heel. If you only walk from the bike to a door, a lighter cover packs smaller and is easier to carry.

Packing, repair and when to skip them

A pair of overboots packs into a space smaller than a water bottle, which makes them easy to carry on every ride. Keep them in a small stuff sack with a repair patch or a roll of tape. A split seam can be taped for a day, but the repair is temporary and the cover should be replaced before the next wet season.

If you already own waterproof riding boots, covers add little beyond protecting the boot's surface and keeping mud off. If your boots are breathable and only lightly water-resistant, covers extend their useful range in heavy rain. Match the cover to the boot rather than buying the cheapest pair and hoping.

Checklist

  • Measure your riding boots, not your shoes.
  • Try the covers on over the boots you actually wear.
  • Check that the top closes above the boot cuff.
  • Confirm the cover sits under the overpant hem.
  • Look for a reinforced shifter patch on the left boot.
  • Check the sole material for grip on pegs and wet ground.
  • Keep the cover clear of the exhaust and engine.
  • Carry a small repair patch or tape.

Questions

Can I walk in rain boot covers?

Short distances, yes, if the cover has a reinforced sole edge. Long walks wear through the sole and heel quickly, and a full-sole cover can be slippery on smooth surfaces. Treat them as protection for the ride, not as walking footwear.

Do boot covers fit over adventure boots?

Some do, but adventure boots are wider and taller than touring boots. Check the stated calf circumference and shaft height, and try them on over your own boots. A cover that is too tight will split at the heel or the seam.

Are boot covers better than waterproof boots?

They solve different problems. A waterproof boot protects the whole foot and is more durable, but it is heavier and slower to dry. Covers are cheap, pack small and extend the life of a water-resistant boot. Many riders use both.

Do boot covers interfere with the gear shifter?

A loose cover can catch on the lever or reduce feel. Choose a close-fitting cover with a shifter patch, and check that it does not bunch under the lever. If the cover moves, stop and adjust it before riding.

Go deeper