A glove label can say CE EN 13594 and still tell you very little until you know what the standard tests. It is not a single pass or fail for the whole glove, and the level number is not a general quality score. Reading it correctly helps you compare gloves that look similar on a shelf.
EN 13594 requirements at a glance
| Requirement | What it checks | How to read it |
|---|---|---|
| Knuckle protection | Impact performance of the knuckle guard | Level 1 or Level 2; Level 2 is higher |
| Abrasion | Material loss under rubbing | Minimum pass, not a ranking |
| Cut resistance | Resistance to a blade | Minimum pass |
| Tear resistance | Resistance to a propagating tear | Minimum pass |
| Restraint | Glove stays on the hand under load | Depends on closure and seams |
| Finger joints | Protection of the finger knuckles | Separate from the main knuckle guard |
What EN 13594 covers
CE EN 13594 is the European standard for protective gloves for motorcycle riders. It sets requirements for abrasion resistance, cut resistance, tear resistance, restraint strength, finger-joint protection and knuckle protection. A glove is tested as a complete product, so the materials, seams and construction all affect the result. Passing means the glove met minimums in those tests, not that it will prevent injury.
Knuckle Levels 1 and 2
Knuckle protection is graded at Level 1 or Level 2, with Level 2 the higher performance level in the standard's impact test. This is the only part of the marking most riders recognise, which is why it gets over-read. A Level 2 knuckle says something about that guard, not about the palm, the seams or the cuff.
Abrasion, cut and tear
Abrasion resistance is tested by rubbing the glove material against an abrasive surface under load. Cut resistance tests how the material resists a blade, and tear resistance tests how it resists a propagating tear. These matter because a glove often fails at a seam or a thin panel before the main leather wears through.
Restraint and finger joints
Restraint tests how well the glove stays on the hand under load, which depends on the closure, the cuff and the seams. Finger-joint protection covers the small knuckles on the back of the fingers, not just the main knuckles. A glove can have a strong main knuckle guard and weak finger protection.
Reading the marking and the limits
The marking identifies the standard, the performance level where applicable and sometimes a pictogram. It does not tell you the fit, the breathability, the drying time or how the glove will age. A glove can meet the standard with a thin palm if it passes the minimum, so the mark is a floor. Look at the construction and the coverage as well.
Other markets and replacement
Outside Europe, requirements differ. The United States has no mandatory federal standard specifically for motorcycle gloves, and other countries apply their own marks and consumer rules. A glove legal where you bought it may not carry the marking expected where you ride. Whatever the mark, replace gloves when the palm, seams or armour are worn.
How the marking is applied
The marking should be on the glove or a label attached to it, together with the manufacturer's identification and the standard number. A pictogram alone is not enough; the performance details should be traceable. If the marking is only on the packaging, keep the packaging or photograph it for your records.
Counterfeit and unbranded gloves can carry a CE mark without a valid test. Buy from a retailer that can explain the standard, and be sceptical of very cheap gloves with a premium-looking knuckle shell. The certification is a claim that should be supported by documentation, not just a logo.
Certification is not fit
A certified glove can still be the wrong shape for your hand. The standard tests a sample, not your fit. Fingers that are too long can catch on levers, and a palm that is too wide can let the knuckle guard rotate. Use the standard to filter, then try the glove on and check the reach to the controls.
The same applies to the cuff. A certified glove with a short cuff may leave the wrist exposed between the glove and the jacket. A longer cuff can close that gap, but only if it fits over or under your sleeve without pressure. Certification and coverage are separate questions.
Checklist
- Look for the CE EN 13594 marking and the stated level.
- Check which parts of the glove are reinforced, not just the knuckles.
- Inspect seams and the palm, where gloves often fail first.
- Confirm the closure holds when you pull the glove off.
- Ask for the manufacturer's documentation if the marking is unclear.
- Remember the standard is a minimum, not a rating of real-world protection.
- Replace gloves with worn palms, torn mesh or damaged armour.
Questions
Is CE EN 13594 mandatory?
In the European Union, motorcycle gloves sold as personal protective equipment must meet the applicable PPE requirements and be CE marked. EN 13594 is the standard used to demonstrate performance. Other countries have different rules, and some have no specific glove standard.
What is the difference between Level 1 and Level 2?
They are knuckle protection performance levels. Level 2 transmits less force in the standard test, so it is the higher grade. The rest of the glove is covered by separate requirements for abrasion, cut, tear, restraint and finger joints.
Does a higher level mean a safer glove overall?
Not necessarily. The level refers to knuckle performance. A Level 1 glove with a reinforced palm, strong seams and a secure cuff can be a better choice than a Level 2 glove that fits badly or has a thin palm.
Can a cheap glove be certified?
Certification depends on meeting the tests, not on price. A cheaper glove can be certified, and an expensive one can be poorly made. Check the marking, the construction and the fit rather than assuming price equals protection.