A tube-type tire relies on an inner tube to hold the air. The tire and rim do not need to seal, which is why tube-type construction remains common on spoked wheels, small scooters and inexpensive commuters. The tube is a wearing component: it flexes with the tire, chafes on the rim strip, and can be pinched during mounting. Most tube failures are installation or pressure problems rather than rubber failure.
Tube-type system
| Part | Job | Common failure |
|---|---|---|
| Inner tube | Holds air | Pinch, chafe, valve tear |
| Rim strip | Protects tube from spokes | Missing, narrow, displaced |
| Valve | Inflate and seal | Cracked, loose |
| Tire casing | Carries load | Cut, cord damage |
| Rim | Supports bead | Bent flange, rough spoke ends |
The tube and the rim strip
The inner tube is a closed loop of butyl or natural rubber with a valve bonded in. It sits inside the tire and inflates against the casing. A rim strip covers the spoke nipples so the tube does not chafe or puncture on them.
A missing, narrow or displaced rim strip is a common cause of repeated punctures on a spoked wheel. If a tube fails on the inside curve, look at the rim strip and the spoke ends before fitting another tube.
Heat and pressure
A tube adds a layer that must flex with the tire. Under-inflation increases that flex, and the tube can overheat and fail. The recommended pressure for a tube-type tire is not lower than for a tubeless tire of the same size; it is set by the load and the vehicle.
Friction between the tube and the tire can also generate heat, especially with a dry or talc-free installation. A little tyre talc helps the tube move, and it makes mounting easier. Do not use oil or grease.
Pinch flats and mounting
A pinch flat happens when the tube is trapped between the tire bead and the rim during mounting, or when the tire is compressed against the rim by an impact. The first is preventable with careful technique; the second is a reason to check pressure and rim condition after a hard hit.
Mounting a tube requires partial inflation before the final bead seat so the tube can settle without folds. A folded tube can rub through in a few hundred kilometres. If the tire will not seat evenly, deflate and start again rather than forcing it.
Repair and replacement
A tube can be patched or replaced. A tire with a tube can sometimes be repaired with a patch on the inside, but the tube still has to be replaced or patched. A sidewall cut, a torn bead or a tire with exposed cord is a replacement regardless of the tube.
Carry a spare tube and the tools to remove the wheel if you ride in areas where a tube failure would leave you stranded. A plug kit does not repair a tube.
When tube-type is the right choice
Tube-type construction suits spoked rims that are not sealed, small wheels where a tubeless bead is difficult to mould, and bikes where a roadside tube change is part of the plan. It is simple and repairable, and the components are inexpensive.
It is not automatically inferior. A well-mounted tube-type tire at the correct pressure can be reliable for years. The disadvantage is the extra component and the heat, not the principle.
Checklist
- Check the rim strip covers every spoke nipple.
- Use tyre talc, never oil, when fitting a tube.
- Inflate partially, settle the tube, then seat the bead.
- Use the vehicle pressure for the load.
- Carry a spare tube on remote rides.
- Replace a tube that has been pinched or overheated.
Questions
Can I fit a tubeless tire with a tube?
Only if the tire and rim manufacturer approve it. A tubeless tire can be used with a tube in some applications, but the bead and rim must still be compatible and the pressure must be correct.
Why do I keep getting punctures on the inside of the tube?
Usually the rim strip, a rough spoke end or a burr on the rim. Inspect the rim with the tube removed and replace the strip if it is narrow or displaced.
Do tube-type tires need different pressure?
No. Use the vehicle manufacturer's pressure for the load. Under-inflation is more damaging to a tube because it increases heat and flex.
Can a tube be patched?
Yes, if the hole is small and the patch is applied correctly. A tube with a torn valve, a large hole or heat damage should be replaced.