The bead is the edge of the tire that sits against the rim flange. Inside it is a bundle of steel wires, wrapped in rubber and protected by a chafer strip. On a tubeless tire the bead also has to seal against the rim, which is why the bead seat and the rim flange must be clean, undamaged and compatible. Most sudden pressure losses at the bead come from mounting damage, corrosion on the rim, or a tire that was run flat and overheated.
Bead problems and causes
| Symptom | Likely cause | Action |
|---|---|---|
| Slow leak at bead | Corrosion or dirt on seat | Clean, inspect, re-seat |
| Leak after mounting | Chafer cut or bead deformed | Replace tire |
| Leak only when hot | Bead not fully seated | Inspect and re-seat |
| Torn chafer | Lever damage or run flat | Replace tire |
| Bent rim flange | Impact | Repair or replace wheel |
| Valve bubbling | Perished valve | Replace valve |
The bead bundle and the chafer
The bead bundle is a loop of high-tensile steel wire. It takes the tension from the casing cords and stops the tire from lifting off the rim under load. Around the bundle, rubber compounds bond the bead to the casing and provide the sealing surface.
The chafer is the abrasion-resistant strip on the outside of the bead. It rubs against the rim flange as the tire flexes. A worn or torn chafer exposes the bead, and a bead that has been run flat often shows a rough, polished or frayed edge. That is a replacement, not a re-seat.
Tubeless sealing
A tubeless tire seals against the rim through contact pressure and the rubber of the bead. The rim must have the correct profile, a clean bead seat and no corrosion or gouges. A new tire on a corroded rim can leak slowly even though the bead looks seated.
The valve is part of the same system. A perished valve grommet, a loose valve nut or a cracked valve stem can mimic a bead leak. Soapy water on the bead and the valve, with the wheel off the bike, is the quickest way to see where the air is going.
Mounting damage
Most bead damage happens during fitting. A lever inserted too deep, a rim clamp overtightened, or a tire forced over a flange can cut the chafer or deform the bead wire. A deformed bead may still hold air cold and lose it when the tire heats and flexes.
A shop that mounts tubeless tires should clean the rim, inspect the bead seat, lubricate with an approved mounting compound and seat the bead with controlled pressure. If the bead will not seat, stop and find out why. More pressure is not a diagnosis.
Bead leaks and run-flat damage
A bead leak can be slow and intermittent. The tire may hold pressure overnight and lose it after a ride. Corrosion, a trapped piece of old rubber, a bent flange or a damaged bead can all produce the same symptom. Re-seating without cleaning the seat usually makes it come back.
Running a tire flat damages the bead and the sidewall. The bead can overheat, the chafer can tear and the casing can be permanently deformed. A tire that has been run flat should be inspected off the rim and replaced if there is any doubt, even if it holds air afterwards.
When to replace
Replace a tire with a torn chafer, exposed bead wire, a deformed bead, a bead that has been run flat, or a bead seat that will not seal after proper cleaning. Do not use sealant to hide a bead leak; it can mask a structural problem and corrode the rim.
If the rim itself is damaged, the wheel needs repair or replacement before a new tire is fitted. A new bead cannot seal against a bent flange. Fix the rim, then fit the tire.
Checklist
- Clean and inspect the bead seat before fitting a tire.
- Check the chafer for cuts and the bead for deformation.
- Replace the valve with the tire when it is rubber and aged.
- Use soapy water on bead and valve to locate a slow leak.
- Never use sealant to hide a bead leak.
- Replace a tire that has been run flat, even if it holds air.
Questions
Can a torn bead be repaired?
No. The bead carries the casing load and seals the air chamber. A torn chafer or exposed wire cannot be restored safely. The tire must be replaced.
Why does my tubeless tire lose air at the bead?
Usually corrosion, dirt or a damaged bead seat prevents a clean seal. A bent rim flange or a deformed bead can do the same. Clean and inspect first; replace if the damage is structural.
Should I use bead sealant?
No. Sealant can mask a leak and corrode the rim. Fix the seat and the bead, or replace the tire.
Can I ride home on a tire that has been run flat?
Only at walking pace and only if the tire still holds air, and even then the tire may be structurally damaged. It should be inspected off the rim before any further use.