A tire size code is a set of nominal dimensions, not a measurement of the tire on your rim. The first number is the section width in millimetres, the second is the sidewall height as a percentage of that width, and the last is the rim diameter in inches. Multiply, add, and you get a nominal overall diameter; multiply by pi and you get a nominal circumference. Those two derived figures explain most of what a size change does: how far the gearing moves, how much the speedometer drifts, how much room the tire needs under a fender. What the arithmetic cannot tell you is the measured width on your particular rim, the loaded radius, or whether the vehicle was approved for the size.

Worked diameters for common sizes

SizeNominal widthSidewall heightRimNominal overall diameterCircumference
110/70-17110 mm77 mm17 in (432 mm)586 mm1841 mm
120/70-17120 mm84 mm17 in (432 mm)600 mm1885 mm
130/70-17130 mm91 mm17 in (432 mm)614 mm1929 mm
90/90-1490 mm81 mm14 in (356 mm)518 mm1627 mm
100/80-14100 mm80 mm14 in (356 mm)516 mm1621 mm
3.50-1088.9 mm88.9 mm (nominal)10 in (254 mm)432 mm1357 mm
120/80-14120 mm96 mm14 in (356 mm)548 mm1721 mm

Splitting the code into three numbers

Take 110/70-17. The 110 is the nominal section width in millimetres, measured at the widest point of the inflated casing. The 70 is the aspect ratio: the sidewall height is 70 per cent of that width, so 77 mm. The 17 is the rim diameter in inches. The letter between the aspect ratio and the rim diameter, usually R, describes the casing; a dash or a letter such as B usually means bias construction. Everything after the size line is load and speed, not dimension.

Inch sizes use a shorter code. 3.50-10 means a nominal width of 3.50 inches on a 10-inch rim, and the missing aspect ratio is conventionally read as roughly 100 per cent, which gives a sidewall close to 89 mm. That convention is why the arithmetic for inch sizes is even more nominal than for metric ones: the real section height depends on the maker and the rim. 90/90-14 sits between the two systems, a metric width and aspect on a small rim.

From sidewall height to overall diameter

The nominal overall diameter is the rim diameter converted to millimetres plus twice the sidewall height. For 110/70-17: 17 × 25.4 = 431.8 mm of rim, 110 × 0.70 = 77 mm of sidewall, so 431.8 + 154 = 585.8 mm. Round it to 586 mm. For 90/90-14: 355.6 mm of rim plus twice 81 mm gives 517.6 mm. The method is identical for every size; only the inputs change.

The result is nominal because the section width is nominal. A tire marked 120/70-17 measured on a wide rim can be wider than 120 mm and sit slightly lower in profile than the arithmetic suggests, while the same tire on a narrow rim can measure under 120 mm and stand taller. Use the calculated figure to compare sizes and estimate ride height, not to promise a millimetre-perfect result.

Circumference, gearing and the speedometer

Multiply the diameter by pi and you get the nominal circumference, the distance one revolution covers. 586 × 3.1416 is about 1841 mm. That number is what the gearing and the speedometer actually see. Going from a 586 mm to a 600 mm diameter adds roughly 44 mm per revolution, about 2.4 per cent, so the bike is geared taller by that margin and the speedometer, which counts revolutions, reads low by roughly the same percentage.

The effect is small but cumulative. Two per cent is a few hundred rpm at highway speed and a few kilometres per hour of indicated error. Change only one wheel and the discrepancy between front and rear grows, which matters on a machine that compares wheel speeds for ABS or traction control. Record the original circumference before changing anything so that the comparison stays honest.

Rim width is the missing variable

Manufacturers measure section width on a specified rim, and the tire's approved rim range appears in the maker's data, sometimes on the sidewall. Fit the same tire to a rim at the wide end of that range and it spreads: wider, slightly lower, flatter across the tread. Fit it at the narrow end and it crowns: narrower, taller, with a more rounded profile. The size code does not change, but the shape does.

This is why two tires with the same numbers can look different side by side, and why a size that fits one bike can rub on another. If the wheel is not original, measure the rim width between the bead flanges before trusting the tire size. A rim outside the tire's approved range is not a fitment question to settle by test riding.

When the arithmetic says yes and the bike says no

A calculated diameter within a few millimetres of the original is a good start and nothing more. The tire still has to clear the fender, the fork sliders, the swingarm and the chain; still has to meet the load index on the vehicle plate; and still has to be a size and construction the vehicle was approved with. Those four checks fail more often than the arithmetic does.

If any of them fails, the answer is the specified size, not a smaller margin. A tire that rubs, a rim outside its range, a load index below the plate or a casing the manual does not list are all reasons to stop. Cuts, bulges or a bent rim found during the check mean the part is replaced or inspected by a professional, not recalculated.

Checklist

  • Write down the full size code from the sidewall, including the construction letter.
  • Convert the rim diameter to millimetres before adding sidewall height.
  • Calculate the nominal diameter and circumference of the original and the candidate size.
  • Compare the two circumferences as a percentage, not as a raw millimetre figure.
  • Measure the rim width between the bead flanges and check it against the tire maker's range.
  • Confirm load index and speed rating against the vehicle plate.
  • Check static and loaded clearance before ordering.

Questions

Can I use the calculated diameter to choose a different size?

Only as a first filter. The calculation shows how overall diameter and circumference change; it says nothing about rim width, clearance, load index, speed rating or whether the vehicle was approved for that size. Use it to rule out sizes that are obviously too tall, then check the rest against the manual and the tire maker's data.

Why does my 120/70-17 measure wider than 120 mm?

Because 120 is a nominal figure measured on a specified rim at a stated pressure. A wider rim spreads the casing and increases the measured width; a narrow rim does the opposite. Manufacturing tolerance also plays a part. The nominal number is for comparing and specifying, not for predicting the exact width on your wheel.

Does a larger diameter raise or lower the gearing?

A larger circumference covers more ground per revolution, so the engine turns fewer times for the same road speed. That is taller gearing: lower rpm at a given speed, and slightly slower acceleration. The speedometer, which counts wheel revolutions, reads lower than actual. The change scales with the circumference difference.

Do I need to recalibrate the speedometer after a size change?

If the new circumference differs from the original by more than a fraction, the indicated speed will drift. Whether it can be corrected depends on the instrument cluster, and correction is not always possible. On a bike with wheel-speed-based ABS or traction control, a large change can affect those systems too. Keep the change small.

Go deeper