An underbone uses 17-inch wheels that are much narrower than a sport bike's. A 70/90-17 front is 70 mm wide with a 63 mm sidewall and a nominal 558 mm diameter; an 80/90-17 rear is 80 mm wide with 72 mm of sidewall and 576 mm. The rear is deliberately taller, which raises gearing and ride height, and a change of 10 mm in section width on a 1.60 inch rim is a far larger proportional change than the same step on a 5.50 inch rim.

Underbone sizes, nominal values

SizeSection (mm)Sidewall (mm)Nominal diameter (mm)Typical rim (in)
70/90-1770635581.40-1.60
80/90-1780725761.60-1.85
90/80-1790725761.85-2.15
100/70-17100705722.15-2.50
110/70-17110775862.50-3.00
120/70-17120846003.00-3.50

The narrow-rim arithmetic

Widths from 70 to 90 mm sit on rims between about 1.40 and 2.15 inches. At that scale the rim is a large fraction of the tire's width, so it decides the tread shape instead of merely supporting it. A 90 mm tire on a 1.60 inch rim is drawn tall and round; the same tire on a 2.15 inch rim is flatter across the crown and puts a different part of the tread on the road.

Aspect ratios are high because the wheels are small and the bikes carry load. A 90 percent sidewall on 80 mm is 72 mm, which is a lot of cushion relative to a 576 mm diameter. The design is buying compliance and rim protection, not style. That is why a low-profile tire on an underbone often feels harsh before it feels sporty.

Why the rear is taller

The rear tire's larger diameter does three things: it raises the tail, it lowers engine speed for a given road speed, and it increases the contact patch slightly. On a small engine the gearing effect is noticeable. Fitting a shorter rear tire makes the engine rev higher at the same speed and lowers the bike, which changes both the ride and the stand clearance.

The speedometer usually reads from the front wheel or the gearbox, depending on the model, so a front size change can affect indicated speed while a rear change affects actual gearing. If the bike has ABS, both wheels feed the system, and a mismatch between the two diameters can change when it intervenes. Check the manual before changing either end.

Pinching a wide tire onto a narrow rim

Fitting a 110/70-17 to a rim designed for an 80/90-17 is a common experiment. The beads are pulled inward, the sidewall bulges and the tread crowns, so the part of the tire touching the road is narrower than the printed width and less evenly supported. Grip does not increase; the tire simply has a worse shape and more unsprung mass.

The reverse is also a problem. A narrow tire on a wide rim is stretched, the sidewall is pulled outward and the bead seat is less secure. Both directions change how the tire warms and wears, and neither is a fitment the vehicle maker approved. Stay inside the rim width range the tire manufacturer publishes for that size.

Daily duty, load and tubes

Underbones work hard: short trips, two riders, rough surfaces, and a pressure check that often does not happen. The load index on a small tire is modest, and a passenger can use most of the margin. A tire that is 10 percent under-inflated for its load deflects more, heats more and wears its shoulders, and on a tube-type wheel the tube is being flexed as well.

Check pressure cold, before the first ride, with a gauge that reads low pressures accurately. Add air for a passenger if the manual gives a loaded figure. Inspect the valve and the rim strip at the same time, because a slow leak on a small wheel can feel like a handling fault before it is obvious as a flat tire.

Clearance and the final fitment check

With the bike on a stand, turn the wheel and watch the gap to the fender, the fork legs, the swingarm and the chain guard. Then compress the suspension and look again, because a tire that clears at rest can touch a fender under braking. Check the exhaust and the centre stand at the rear, where a wider tire usually runs closest.

Finish by confirming the sidewall against the manual: size, load index, speed rating and tube type. If the printed size is not listed, the tire is not approved for the machine even when it fits. Record the size and the date, and re-check pressure after the first ride, when a new tire has fully seated on the rim.

Checklist

  • Note the front and rear sizes from the manual, including load index.
  • Read the rim width before considering a wider tire.
  • Confirm the wheel needs a tube or is tubeless.
  • Check fender, chain guard and centre stand clearance at full compression.
  • Set cold pressure from the label and add air for a passenger if specified.
  • Inspect the valve and rim strip whenever the tire is off.
  • Replace both tires together if the manual treats them as a pair.

Questions

Can I put a 110/70-17 on the rear of my underbone?

Only if the manual lists that size and the rim is wide enough. A 1.60 or 1.85 inch rim pinches a 110 section, so the tread crowns and the contact patch does not grow as expected. Check the rim range and the swingarm clearance first.

Why is the rear tire taller than the front?

A taller rear raises gearing and ride height while the front stays low for steering. It is a deliberate pairing for small engines. Replacing it with a shorter tire changes engine speed at a given road speed and lowers the bike.

Do underbone tires always need tubes?

No. Many use cast wheels and tubeless tires, while spoked or older wheels need tubes. The sidewall and the rim decide, not the model year. A tubeless tire on an unsealed spoked rim will leak at the nipples.

How often should I check pressure?

Before the first ride of the day is the reliable routine, and always before a trip with a passenger. Small tires hold little air, so a small loss is a large percentage change and affects handling quickly.

Go deeper