110/70-17 decodes to a 110 mm nominal section, a sidewall that is 70 percent of that width, 77 mm, and a 17-inch rim. The nominal overall diameter is 431.8 mm plus 154 mm, about 586 mm. Those three numbers fix the rim width the tire needs, the load the casing is approved to carry and the clearance it requires. The size appears on light sport and commuter machines, and on the rear of some underbones, but the manual and the rim markings decide the fitment for a particular bike.
Sizes near 110/70-17, nominal values
| Size | Section (mm) | Sidewall (mm) | Nominal diameter (mm) | Change vs 110/70-17 (mm) |
|---|---|---|---|---|
| 100/70-17 | 100 | 70 | 572 | -14 |
| 100/80-17 | 100 | 80 | 592 | +6 |
| 110/70-17 | 110 | 77 | 586 | 0 |
| 110/80-17 | 110 | 88 | 608 | +22 |
| 120/60-17 | 120 | 72 | 576 | -10 |
| 120/70-17 | 120 | 84 | 600 | +14 |
| 130/70-17 | 130 | 91 | 614 | +28 |
What each number controls
The 110 is measured across the widest part of the inflated casing on a design rim, not across the tread. The 70 gives sidewall height as a percentage of the section, so 77 mm here. The 17 is the rim seat diameter in inches. The diameter figure of 586 mm is arithmetic: rim diameter times 25.4, plus twice the sidewall. Real tires vary by a few millimetres between makers and constructions.
The load index and speed symbol follow the size on the sidewall, and they are part of the approval rather than decoration. A 110/70-17 can be built with different casings and load indexes for different motorcycles. Two tires with the same printed size can therefore have different load ceilings and sidewall stiffness, which is why the full sidewall line matters more than the size alone.
What class of machine the size suits
The diameter and the narrow section point to a light machine. A 586 mm wheel is smaller than the 600 mm front common on larger sport bikes, and 110 mm of width is a front rather than a rear on most road bikes. The size suits light sport and commuter models, and small-capacity machines where the front carries a modest load and steering effort has to stay low.
It is also used at the rear of some underbones and small commuters, where the same tire carries drive load on a narrow rim. That dual use is a reminder that a size does not belong to a category. Check whether the machine lists 110/70-17 as a front or rear fitment, and confirm the load index for that position before assuming anything from the width.
Verifying fitment against the manual and the rim
Open the manual or read the vehicle plate and note the listed size, load index and speed rating for each wheel. Then read the rim: the width is usually cast or stamped as 2.50x17 or 3.00x17. A 110/70-17 is normally designed around a rim between about 2.50 and 3.00 inches. Outside that window the tread profile changes even though the tire mounts and holds air.
Then check clearances: the front fender at full fork compression, the brake caliper and hose, and the gap to the fork leg. On a rear fitment, check the chain guard, the swingarm and the hugger. A tire can be correctly sized and still foul a component because a previous owner changed the wheel, the mudguard or the brake setup.
What changes with a different size
Going to 120/70-17 adds 10 mm of width and 7 mm of sidewall, so the diameter grows by about 14 mm. The front of the bike rises, steering slows slightly, and the wider tread needs a wider rim to keep its shape. Going to 110/80-17 adds 11 mm of sidewall and about 22 mm of diameter, a larger geometry change than most riders expect from one step.
Going down to 100/70-17 reduces width by 10 mm and diameter by about 14 mm, which lowers the front and quickens steering. It also reduces the load the tire can carry. Any of these changes alters the speedometer reading, the clearance to the fender and the balance between front and rear, so treat a size change as a geometry change rather than a cosmetic one.
Load, pressure and wear on this size
Set pressure cold from the vehicle label. The sidewall maximum is a ceiling, not a recommendation, and it is usually much higher than the bike needs. On a light machine the correct pressure is low enough that a small error is proportionally large, so use a gauge that reads accurately at low values and check before the first ride of the day.
Watch the wear pattern. A narrow front on a light bike often wears the shoulders first if the pressure is low, and the centre first if the bike spends its life upright on abrasive asphalt. Cupping on the shoulders points to pressure, damping or balance. Replace at the wear indicator, and inspect the sidewall for cracking at the same time.
Checklist
- Read the manual's size, load index and speed rating for the position.
- Check the rim width stamp against the tire maker's window.
- Measure the fitted tire's width and diameter before ordering a replacement.
- Confirm the fork and fender clear at full compression.
- Set cold pressure from the label and re-check after the first ride.
- Inspect for shoulder cupping and sidewall cracking at every pressure check.
- Replace the tire if a bulge or a cut to cord appears after an impact.
Questions
What does 70 mean in 110/70-17?
It is the aspect ratio: the sidewall height is 70 percent of the 110 mm section, which gives 77 mm. Add two sidewalls to the 17-inch rim diameter and the nominal overall diameter is about 586 mm. Nominal values vary slightly between makers.
Is 110/70-17 a front or a rear size?
It can be either. On most road bikes it is a front, while some underbones and small commuters use it at the rear. Position is decided by the manual, and the load index for a rear fitment is usually higher because it carries drive load.
Can I use a 120/70-17 instead?
Only if the manual allows it and the rim is wide enough. The diameter grows by about 14 mm, which raises the front and slows steering, and the wider tread needs a wider rim. It is a geometry change, not a direct substitution.
How do I know the rim is wide enough?
The wheel carries a stamp such as 2.50x17, meaning 2.50 inches wide and 17 inches in diameter. Compare it with the range the tire manufacturer publishes for 110/70-17, usually about 2.50 to 3.00 inches.