Three notations describe the same interface: metric sizes such as 110/70-17, inch sizes such as 3.50-10, and alpha codes such as MT90-16. They are not three ways of writing one measurement. Metric sizes give a nominal width in millimetres and an aspect ratio; inch sizes give a nominal width in inches and usually assume a sidewall close to the width; alpha codes pack a width band and an aspect ratio into letters and digits. Converting between them is therefore arithmetic followed by a warning label.

Nominal size arithmetic across formats

CodeNominal widthNominal sidewallRimNominal diameter
3.50-1088.9 mm88.9 mm10 in432 mm
4.00-18101.6 mm101.6 mm18 in660 mm
90/90-1490 mm81 mm14 in518 mm
100/80-14100 mm80 mm14 in516 mm
110/70-17110 mm77 mm17 in586 mm
120/70-17120 mm84 mm17 in600 mm
130/70-17130 mm91 mm17 in614 mm
150/70-17150 mm105 mm17 in642 mm

What each notation encodes

A metric size such as 110/70-17 gives a nominal width in millimetres, an aspect ratio as a percentage and a rim diameter in inches. An inch size such as 3.50-10 gives a nominal width in inches and a rim diameter, with the aspect ratio left to convention. An alpha code such as MT90-16 uses a letter group for a width band and a two-digit aspect ratio before the rim diameter.

The three systems grew from different manufacturing traditions, and they do not measure the same thing in the same place. That is why a conversion is an approximation even when the arithmetic is exact. The number you calculate is a nominal equivalent, and it does not by itself establish that the two tires are interchangeable on a given rim.

Metric to inch is not a straight swap

Divide millimetres by 25.4 and you have inches: 110 mm is 4.33 in, 120 mm is 4.72 in, and 3.50 in is 88.9 mm. That arithmetic is useful for comparing a metric candidate with an inch size, and for estimating overall diameter. It is not enough to convert a specification, because the inch figure is a commercial size rather than a measured section width on a stated rim.

The diameters can still land close. A 4.00-18 works out at about 660 mm overall, and a 110/90-18 at about 655 mm, so the two are near neighbours in height while differing in width and in the way the size is defined. Close is the right word: check the actual tire's published data before treating them as equivalents.

Alpha codes and the charts

Alpha codes pack information tightly. The letter group encodes a width band, the two digits give the aspect ratio and the final number is the rim diameter. Charts commonly pair an alpha size with a metric size, and those pairings are useful starting points for a search. They are not approvals, and different makers may map the same letters to slightly different widths.

Some alpha sizes are position-specific, appearing mainly as front or rear fitments on older machines. If a chart offers a metric equivalent, compare the calculated diameter, the load index and the rim width range before ordering. The sidewall of the tire you are replacing is the most reliable record of what the bike was built around.

Keep the diameter close

When converting, the diameter is the figure to preserve. A change of a few millimetres affects ride height, gearing and the speedometer by a small amount; a change of 20 mm or more is obvious in all three and can close a fender gap. Calculate both diameters and compare them as a percentage before deciding that the sizes match.

Aspect ratio and width trade against each other to hold the diameter. A wider tire needs a lower aspect ratio to stay the same height, and a narrower tire needs a higher one. If the candidate size cannot keep the diameter close, the conversion has become a size change, with all the clearance and approval questions that follow.

What conversion cannot answer

No conversion table states the load index, the speed rating, the construction or the approved rim width for a given tire. Those are properties of the individual product, and they have to be read from its sidewall and its maker's data. A converted size that matches in diameter can still be under-rated, bias instead of radial, or outside the rim's range.

Work in a fixed order: read the original sidewall, calculate the nominal diameter and circumference, find the candidate's published dimensions and approved rim range, then check the load index and speed rating against the vehicle plate. If any step fails, the candidate is out. Damage found along the way, such as a cut, bulge or cord, means replacement or inspection, not another conversion.

Checklist

  • Read the original size from the sidewall, not from a parts listing.
  • Identify which notation the code uses before calculating anything.
  • Convert the rim diameter to millimetres for every comparison.
  • Compare nominal diameters as a percentage, not just as a number.
  • Look up the candidate's approved rim width range and measured data.
  • Check load index and speed rating against the vehicle plate.
  • Confirm clearance before ordering, especially for inch-to-metric swaps.

Questions

Is a 3.50-10 the same as a 90/90-10?

Close in nominal width, not identical in specification. 3.50 in is 88.9 mm, and the inch size conventionally assumes a sidewall near the width, which gives a different diameter from a 90/90. The load index, construction and rim range may also differ. Use the conversion as a starting point, then check the actual tire's data.

Can I replace an alpha size with a metric one?

Sometimes, if the calculated diameter is close, the rim width range is respected and the load index and speed rating meet the plate. Alpha charts give a nominal pairing, not an approval. On older machines the front and rear may use different alpha conventions, so check each position separately.

Why do conversion tables disagree with each other?

Because they round differently, use different nominal rim widths for the measurement, or map a width band to a range of metric sizes. None of them is measuring your tire. The sidewall of the product and the maker's published dimensions are the figures that matter when the difference is small.

Does converting a size change the speedometer?

It can, if the overall diameter changes. A conversion that keeps the diameter close leaves the speedometer roughly correct; one that raises or lowers it by 20 mm produces a noticeable error. Calculate the circumference of both sizes before assuming that a converted size is dimensionally equivalent.

Go deeper